Skip to content

Step by step

How to estimate materials for an extension or room addition

An extension is not a room, and that is why estimating one by hand goes wrong. Some of its walls face the weather and at least one does not, so cladding, render and external insulation belong to part of the perimeter while boarding and paint belong to all of it. Draw it against the house and that split happens by itself — a wall counts as an outside wall unless another room is on the other side of it.

Free to use. Every price and assumption is yours to change. Picking the trades for a surface →

See the split on your own footprint

Give it the size of the extension and how many sides meet the existing house. The outside wall area is what cladding and render are bought against; the inside face is every wall, including the one onto the house. Set the sides joined to zero and watch the two converge — that is a garden room.

Your extension

Sides joined to the house
Outside doors
Windows
Floor / slab12.0 m²

Concrete, insulation under it, screed or levelling compound, the floor finish, underfloor heating

Outside wall, net19.2 m²

Cladding, render and external insulation — bought against this, not against the whole perimeter

Wall onto the house9.6 m²

No cladding, no render, no external insulation. Finished on the inside only

Inside wall face, net28.8 m²

Plasterboard, insulation between the studs, paint or tiles — every wall has one

Ceiling / roof footprint12.0 m²

Ceiling finishes, and the plan area a roof covering is worked out from

One side joined: 4.00 m of the 14.00 m perimeter is wall onto the house, leaving 10.00 m outside. 1 outside door at 0.90 m × 2.10 m and 2 windows at 1.20 m × 1.20 m come off — the planner's own default sizes, and every opening is resizable there. Draw it instead and no wall has to be declared as outside wall: a wall is one unless another room is on the other side of it.

The whole way through

  1. 1

    Draw the existing room first, then the extension onto it

    The order matters. An extension drawn on its own is a shed; drawn against the room it opens into, it is an extension.

    • ·Sketch the room the extension comes off — it does not have to be exact, and you can correct it later. What it is there for is to give the new walls something to be joined to.
    • ·Draw the new footprint so its back wall runs along the existing wall, corner to corner. Snapping takes care of the rest.
    • ·Everything that follows comes off that drawing, so there is no second set of measurements to keep in step with it.
  2. 2

    Let the walls sort themselves out

    Nothing has to be declared as an outside wall. A wall is one unless another room is on the other side of it.

    • ·Select a wall and the panel adds an Exterior materials section — but only for the walls that face the weather. The wall onto the house does not get one, because it is not one.
    • ·That is the whole difference between costing an extension and costing a room, and it is the part people get wrong by hand: cladding and render ordered against the full perimeter, on a wall that will never see daylight.
    • ·Move the extension later and the split follows. Nothing is stored as a flag that can go stale.
  3. 3

    Build the floor up from the ground

    The Floor tab holds the whole build-up in the order it is laid, each priced off the same footprint.

    • ·A slab is worked out as area × thickness, with the default at 100 mm, and returned as a volume and a bag count.
    • ·Insulation under it, levelling compound over it, then the finish — tiles, boards or whatever you have chosen — each read the same area.
    • ·Underfloor heating sits here too, because it is a floor trade. It picks a real stock element rather than cutting a cable to fit.
  4. 4

    Take the outside walls on their own

    Select each outside wall and tick what it carries: cladding, render, external insulation. Those are bought against that wall’s net area.

    • ·Net, not gross: openings come off. On an extension, where most of the glazing is on two or three walls, that difference is not small.
    • ·Each wall is costed separately, so a rendered flank and a clad rear elevation are two different numbers rather than one average.
    • ·Any note you add to a wall travels with it into the printed list — useful for "this one gets the sliding doors".
  5. 5

    Then the inside face of every wall, joined or not

    Every wall has an inside face, including the one onto the house. Boarding, insulating and painting are counted across the whole perimeter.

    • ·The Walls tab, with no single wall selected, works on the room: stud framing, insulation between it, plasterboard, then paint, tiles or wallpaper.
    • ·Select one wall instead and you override the room-wide choice for that wall only — the tiled wall in a new kitchen, say, where the rest is painted.
    • ·The ceiling is its own tab, taking the footprint area: boarding, insulation above it, and paint.
  6. 6

    Know what the planner does not do

    The roof covering and the structure are not here, and this is not a building-regulations check. Both are better said than skirted.

    • ·The roof: the planner gives you the plan area and nothing else. Take that figure to the roofing calculator, which asks for the pitch, and save the result into the same project so it lands in the same total.
    • ·The structure: nothing here sizes a beam over the opening you are knocking through, a lintel, a padstone or a foundation. A slab thickness is not a foundation design.
    • ·The rules: no page on this site tells you what your local regulations require, what needs approval or how deep a footing goes where you live. The numbers are for planning and for comparing quotes.
  7. 7

    Link it to a project and let it total up

    Link the plan to a project and the extension arrives in that project’s budget as a room, with every surface under it.

    • ·Calculators saved from elsewhere — the roofing one, groundworks, anything with its own page — land in the same project and the same total.
    • ·Labour is counted separately from materials and priced at the rate you set per trade, so the materials figure stays a materials figure.
    • ·Then the shopping list prints as one order list, in the units merchants actually sell in.

What each surface carries

SurfaceMeasured asWhat you can tick on it
FloorFootprintConcrete slab, insulation, levelling compound, boards, tiles, underfloor heating
Outside wallThat wall’s net areaCladding, render, external insulation, exterior tiling
Wall onto the houseThat wall’s net areaInside face only — framing, insulation, plasterboard, paint, tiles, wallpaper
Walls, as a roomNet area of all of themThe same inside finishes, applied to every wall at once
CeilingFootprintPlasterboard, insulation, paint
Roof coveringNot hereThe roofing calculator — give it the plan area and the pitch

Net area is the number materials are bought against: gross wall area with the doors and windows taken out. An extension is mostly glass on the side facing the garden, so the gap between gross and net is wider here than anywhere else in a house.

What this is not

What the work involves

The planner counts the materials. These explain what is being built with them.

Common questions

Why not just use a material calculator for an extension?

Because an extension is not one surface. It is a slab, three or four walls that are not alike, a ceiling, a roof and the openings between them — and a calculator answers one of those at a time, which leaves you adding up six answers by hand and reconciling six sets of measurements. Drawing it once and ticking the trades on each surface is the same work done in the order the building is actually made.

Do I have to tell it which walls are outside walls?

No. A wall is treated as an outside wall unless another room on the same storey has a wall running between the same two points. Draw the extension onto the room it opens into and the shared wall stops being an outside wall on its own — and starts again if you move the extension away. There is no flag to set, and none to forget.

Does it work out the roof?

Not the covering. The planner gives you the plan area of the extension, which is the figure a roof is estimated from, but a roof is bigger than the ground it covers and the multiplier is the pitch. Take the plan area to the roofing calculator, which asks for the pitch and returns tiles, battens, underlay and ridge, and save that into the same project so it totals with everything else.

Does it size the beam over the opening, or the foundations?

No, and nothing on this site does. Knocking a wall out of the back of a house is structural work, and the beam, its bearings and the foundations under the new walls are an engineer’s calculation, not an estimator’s. The floor slab here is an area times a thickness you choose — a quantity, not a foundation design. Get the structure specified and then come back and count what it is made of.

Can I do a two-storey extension?

Yes. The planner holds up to five storeys, as a row of chips above the drawing with a + to add one, and each is drawn separately. Walls are compared against other rooms on the same storey, so the first-floor extension gets its own split between outside walls and the wall onto the house.

What about a side return or a wrap-around?

Same thing — draw the shape you are actually building. Two sides against the house means two walls stop being outside walls, and the live figures above show that split for a footprint you type in. An L-shaped footprint is drawn corner by corner rather than as a rectangle.

Is a garden room or a detached annexe different?

Only in that nothing is joined, so every wall is an outside wall and carries cladding or render. Everything else is the same drawing and the same surfaces. Set the sides joined to zero in the figures above to see it.

Does this need a paid plan?

Drawing the extension, ticking its trades and reading the costs is free and stays on your own device. The free plan closes two rooms in a plan, which covers an extension and the room it opens into, and allows one project and three saved calculations. The plan document — floor plans, the materials list and the schedules — needs a paid plan, and only Pro gets it without a watermark. Print and PNG work on the free plan, watermarked.

Free to try — no sign-up, nothing to install. The whole job, in seven steps →

Free to try — no sign-up

Draw it once. Every trade prices itself.

Measure the room on screen and its floor, wall and ceiling areas fill the calculators in for you — insulation, boards, paint, tiles — each with its own quantity and cost against one running total.

Free covers one project, three saved calculations and a two-room plan. What a Project Pass adds →

Quantities, hours and costs are estimates for planning and for comparing quotes. They are not a design, a structural calculation, a certificate or a compliance check, and nothing here says what your local rules require or what needs approval. An extension is structural work: have the beams, bearings and foundations specified by someone qualified, and check quantities and prices before ordering.